Vehicles
50 not categorized PORSCHE 924S BUSHING SETCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection
$46.20
Make a selection 54610190150
View/Change Diagram
From $479.60
Make a selection 54610190175
View/Change Diagram
$476.30
Make a selection 54610190160
View/Change Diagram
From $476.30
Make a selection 61610013890
General Fitment356 1960-65
From $438.90
Make a selection 61610013050
View/Change Diagram
$1,156.10
Make a selection P904785 Forged from the highest quality steel, each torsion bar is centerlessly ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. All performance products torsion bars are guaranteed for 3 years against breakage. Note: worn torsion bar bushings will shorten the life of torsion bars. Our 3-year guarantee will remain valid only when bushings are in good condition at time of installing new torsion bars. Sold in pairs. General Fitment924 1976-79924 1980-85 924 1986-88 944 1989-91 944 1985-88 944 1982-85 968 1992-95
$375.00
Make a selection P911955 Forged from the highest quality steel, each torsion bar is centerlessly ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. Guaranteed for 3 years against breakage. Note: worn torsion bar bushings will shorten the life of torsion bars. Our 3-year guarantee will remain valid only when bushings are in good condition at time of installing new torsion bars. Sold in pairs. General Fitment924 1976-79924 1980-85 924 1986-88 944 1989-91 944 1985-88 944 1982-85 968 1992-95
$315.00
Make a selection P909218 Forged from the highest quality steel, each torsion bar is centerlessly ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. All performance products torsion bars are guaranteed for 3 years against breakage. Note: worn torsion bar bushings will shorten the life of torsion bars. Our 3-year guarantee will remain valid only when bushings are in good condition at time of installing new torsion bars. Sold in pairs. General Fitment924 1976-79924 1980-85 924 1986-88 944 1989-91 944 1985-88 944 1982-85 968 1992-95
$341.99
Make a selection 039105401S Often overlooked in a rebuild, worn rod bushings or an absent rod will cause vibration and/or engine noise. Our precisely balanced and rebushed set eliminates the gamble and insures long life to your rebuild. Sold on an exchange basis only. There is a core charge, which is refundable upon receiving your rebuildable part. General Fitment914 1970-76
$291.50
Make a selection 372642739 Weltmeister® front camber plate set, 996/997 Boxster® & Cayman® General Fitment911 1998-05911 2005-08 BOXSTER 1997-04 BOXSTER 2005-08 CAYMAN 2006-08
$450.00
Make a selection 91133300905 Our rear spring plate set is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. The adjustability allows for precise re-indexing of the torsion bar 1 ½ inches up or down. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on without the hassle of adding new bushings. Each plate is clearly marked for indexing purposes and includes complete installation instructions. Features: made from ¼ inch spring steel adjustment range of 1 ½ inches up or down includes new OEM spec. (65 shore) rubber bushings clearly marked for accurate installation and indexing made in Germany sold individually. 2 necessary per car. Plea...(choose a part on the right to read more) View/Change Diagram
From $273.90
Make a selection 910165 Forged from the highest quality steel, each torsion bar is centerlessly ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. All torsion bars are guaranteed for 3 years against breakage. Note: worn torsion bar bushings will shorten the life of torsion bars. Our 3-year guarantee will remain valid only when bushings are in good condition at time of installing new torsion bars. Sold in pairs. General Fitment911 1974-77911 1978-83 911 1984-86 911 1987-89 930 1975-77 911 1970-73 911 1965-69 912 1965-69 914 1970-76
$458.05
Make a selection 904788 Forged from the highest quality steel, each torsion bar is ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. All performance products torsion bars are guaranteed for 3 years against breakage. Note: worn torsion bar bushings will shorten the life of torsion bars. Our 3-year guarantee will remain valid only when bushings are in good condition at time of installing new torsion bars. Sold in pairs. General Fitment914 1970-76
$370.99
Make a selection 91110190160 Genuine complete set of bearings (including # 8) sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Set includes: 1 qty. Crankshaft main bushing sleeve - bushing viii - oversize +0.25mm 12 qty. Crankshaft main bearing shells ii-vii (half) - oversize +0.25mm 2 qty. Crankshaft main bearing shells i (half) - oversize +0.25mm sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment. View/Change Diagram
$1,039.56
Make a selection 91133300902 Our rear spring plate set is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. The adjustability allows for precise re-indexing of the torsion bar 1 ½ inches up or down. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on without the hassle of adding new bushings. Each plate is clearly marked for indexing purposes and includes complete installation instructions. Features: made from ¼ inch spring steel adjustment range of 1 ½ inches up or down includes new OEM spec. (65 shore) rubber bushings clearly marked for accurate installation and indexing made in Germany sold individually. 2 necessary per car. Plea...(choose a part on the right to read more) View/Change Diagram
$363.00
Make a selection FVD205996003VAG These bushings are made for h&r front sway bars with 25 mm diameters. They are a direct replacement for our part # . These will also work on any bar with a 25-mm diameter. If you would also like to replace the rear, please use part # FVD205996003hag sold as a front set. 1 set needed per car.
$58.30
Make a selection AP997TT230 In the quest to create the most well balanced suspension for the 997 turbo, agency power has developed these sway bars to our specifications. The all wheel drive Porsche turbo cars naturally have a lot of under steer. Under steer is when you take a turn but your car keeps going outwards. With an awd car, getting the rear end around can be easily done with a larger sway bar. However you do not want to induce to much over steer as then you will be throttle steering or sent into a drift. With the combination of a properly balanced front and rear sway bar, your car will handle turns much more neutrally and quickly. The sway bars are designed to stiffen up the chassis as well to reduce body roll. Some times called â...(choose a part on the right to read more) General Fitment911 2005-08
$299.95
Make a selection 20934HDC4 The clutch masters fx400 system uses the power plus i pressure plate with a custom, extremely durable, sprung ceramic disc. Sprung disks can be used with the OEM flywheel or aftermarket lightweight flywheels. This is the ultimate extreme duty street and/or road/drag racing system. It is available in a 4 puck configuration, which is very aggressive and not recommended for a street setup. General Fitment911 GT3 2003-05911 TURBO/GT2 2001-05 911 TURBO/GT2 2007-09
$2,644.52
Make a selection AP996200 Racing is part of every Porsche owner's desire. Going fast is one thing, but giving your car the best handling possible is where you will excel as a driver. Agency power industries has developed these adjustable control arms for your Porsche 996 and 997 vehicle. These control arms fit on the rear of your car and help in adjusting camber and toe. In additional to being fully adjustable, these control arms offer increased rigidity from the replacement of the factory urethane bushing with spherical bearing ends. The 6061 cnc machined arms are anodized in our beautiful brilliant blue color and notched for easy adjustment. Each spherical bearing has cnc machined stainless steel fittings for a secure and safe fit. C...(choose a part on the right to read more) General Fitment911 1998-05911 TURBO/GT2 2001-05 911 GT3 2003-05 911 2005-08 911 GT3 2007-11
$625.95
Make a selection ER2221800 Elephant racing monoballs deliver precise, razor sharp handling. but rapid wear has made them impractical for all but the most serious racers. Not anymore! These proprietary-design monoball cartridges have weather seals to keep dirt out and extend product life. this is the only monoball suitable for street or extended track use. dirt and water contaminate ordinary products and accelerate wear. Today’s sticky tire compounds generate corner loads that easily compress factory rubber bushings causing wandering alignment settings. Camber and toe flop around unpredictably. The sealed monoball cartridges replace compliant factory rubber bushings with hardened-steel spherical bearings. Unlike poly bushings that bi...(choose a part on the right to read more) General Fitment944 1982-85924 1976-79 924 1980-85 924 1986-88 944 1985-88 944 1989-91 968 1992-95
$350.00
Make a selection ER2011000 Monoballs deliver precise, razor sharp handling. but rapid wear has made them impractical for all but the most serious racers. Not anymore! Weather seals - our proprietary-design monoball cartridges have weather seals to keep dirt out and extend product life. this is the only monoball suitable for street or extended track use. dirt and water contaminate ordinary products and accelerate wear. Performance - today’s sticky tire compounds generate corner loads that easily compress factory rubber bushings causing wandering alignment settings. Camber and toe flop around upredictably. weather-sealed monoball cartridges replace compliant factory rubber bushings with hardened-steel spherical bearings. Unlike...(choose a part on the right to read more) General Fitment914 1970-76911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 912 1965-69
$299.95
Make a selection 911942 Forged from the highest quality steel, each torsion bar is ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. All performance products torsion bars are guaranteed for 3 years against breakage. Note: worn torsion bar bushings will shorten the life of torsion bars. Our 3-year guarantee will remain valid only when bushings are in good condition at time of installing new torsion bars. 21.6mm effective rate. Sold in pairs. General Fitment914 1970-76
$500.00
Make a selection ER2051500 High performance bushing replacement, no squeaks! Want to experience precision driving, faster lap times, improved road feel and feedback? These patented elephant racing polybronze suspension bearings set a new standard for performance, ride quality and ease-of -installation. Polybronze have a rigid bronze bearing core that does not deform. The polyurethane jacket absorbs mount irregularities while the bronze inner bearing remains true, providing a free-moving machined-fit that rides on a precision race. provided grease fittings make re-lubrication a breeze and a figure 8 groove keeps grease in place. The combination delivers zero squeaks and friction-free suspension movement. well suited to street or track, ...(choose a part on the right to read more) General Fitment911 1965-69912 1965-69 914 1970-76 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$288.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |